Fiber Optic Passive
Fiber Optic Bulk Cable
Fiber Optic Jumpers
Fiber Optic Pigtails
Fiber Optic Connectors
Fiber Optic Adapters
Fiber Optic Attenuators
Loopback Assembly
Fiber Optic Splitter
MPO/MTP Series
Fiber Optic Active
Media Converter
Optical Transceiver
CWDM,DWDM,OADM
Structured Cabling Products
Lan Cable
Patch Cables
Patch Panel
Keystone Jack
110 Wiring Block
Cable Management
Face Plate and Surface Mount Box
MINI SAS8088
Newsletter
for wholesale
about the latest offers and deals Subscribe today!

1000M Fiber media converter
The media converter transform the transmission media of Ethernet signal from CAT5 to optical fiber. it can extend the transmission distance to several kilometer or hundred kilometer.
Description
Brief introduction
This product supports IEEE802.3z 1000Base-Tx/Fx protocol, as well as full duplex and half duplex mode. This manual is for 1000M transceivers.

Installation
1. Interface
RJ-45 interface
The transmission media adopts CAT5 twisted-pair with typical length of 1000 meter. It features the function of automatically identifying the through line and cross wire
Fiber interface
SC/ST fiber interface is of duplex mode type, including two interfaces, namely TX and RX. When the two sets of optical transceiver are interfaced or connected to switch with fiber interface, the fiber is in cross connection, namely "TX-RX", "RX-TX" (direct butting for single optical fiber).

2. Connection
The network device (work station, hub or switch) with RJ-45 interface is connected to RJ-45 jack of optical transceiver through twisted-pair. And the multi/single mode fiber is connected to SC/ST fiber interface of the optical transceiver. Then switch on. The corresponding LED is on for correct connection. (See the table below for the LED indicator lamp)

Technical parameters:
1. Standard Protocol: IEEE 802.3z 1000Base-TX/FX standard
2.Connector:oneUTPRJ-45connector,oneSC/STconnector
3. Operation mode: full duplex mode or half duplex mode
4. Power supply parameter:
outside: 5V DC 2A
built-in: 110-265V AC  48VDC
5. Environmental temperature: <60
6. Relative humidity: 5%-90%
7. TP cable: Cat5 UTP cable
8. Transfer fiber:
multi-mode: 50/125, 62.5/125 or 100/140μm
single mode:: 8.3/125, 8.7/125, 9/125 or 10/125μm


Ordering information:

Description

Fiber mode

TX power

Rx power

Wavelength

Distance

  OP-8110GMA-11-05

Multi-mode dual fiber

-17~-12

<<-20.0

850nm

550m

OP-8110GMA-11-2

Multi-mode dual fiber

-17~-12

<<-20.0

1310nm

2 Km

OP-8110GSA-11-10

Single-mode dual fiber

-6~-12

<<-21.0

1310nm

10 Km

OP-8110GSA-11-20

Single-mode dual fiber

-3~-8

<<-23.0

1310nm

20 Km

OP-8110GSA-11-40

Single-mode dual fiber

-3~0

<<-25.0

1550nm

40 Km

OP-8110GSA-11-60

Single-mode dual fiber

1550nm

60 Km

OP-8110GSA-11-80

Single-mode dual fiber

>>1

<<-27.0

1550nm

80 Km

OP-8110GSB-11-10A/B

Single-mode single fiber

-10~-5

<<-20.0

A side:Tx1310nm/Rx1550nm 
B side:Tx1550nm/Rx1310nm

10 Km

OP-8110GSB-11-20A/B

Single-mode single fiber

-8~-3

<<-23.0

A side:Tx1310nm/Rx1550nm 
B side:Tx1550nm/Rx1310nm

20 Km

OP-8110GSB-11-40A/B

Single-mode single fiber

-3~-0

<<-23.0

A side:Tx1310nm/Rx1550nm 
B side:Tx1550nm/Rx1310nm

40Km

OP-8110GSB-11-60A/B

Single-mode single fiber

-3~-0

<<-23.0

A side:Tx1310nm/Rx1550nm 
B side:Tx1550nm/Rx1310nm

60Km